AutoSCP Solutions - Spick & Span Disinfector

Composition
  • Didecyl dimethyl ammonium chloride : 8.7 %
  • n-alkyl dimethyl benzyl ammonium chloride: 8.19 %
  • Lauryl dimethyl amine oxide
  • Ethylene diamine tetra acetic acid sodium salt
  • Sodium bicarbonate
  • Sodium hypochlorite
Features and benefits
  • N-alkyl dimethyl benzyl ammonium & Didecyl dimethyl ammonium chloride – Combination of most potent QAC’s – Broad spectrum kill
  • Aldehyde free product – No negative occupational hazard – Eco friendly and user friendly
  • Cleaner and disinfectant – Single shot product – Time and cost effective
Directions for use: FOGGING: Transfer the AutoSCP Solutions – Spick & Span Disinfector solution in the fogging machine. Wet surfaces of tiled walls, trolleys, Operation tables & floors evenly. Close rooms & allow to dry for 1 hour.
Instrument disinfection : Ready to use
  • High level disinfection – Soak completely inside the AutoSCP Solutions – Spick & Span Disinfector solution. For semi-critical instruments disinfection, 30 minutes of contact time is required.
  • Sterilisation – For sterilisation 10 hours of contact time is required. Avoid bubble formation. Use a plastic recipient and this should be closed during all the time instruments are soaked in. Take off all the instruments and rinse with sterile water or 0.9 % Na CI solution in sterile water.
Technical data :-
  • Appearance      : Blue liquid
  • Odour                  : Characteristic
  •  pH                         : 9-10
  • Density               : 0.98 -1.04 gm/cm3
The above data is typical of normal production and should not be taken as a specification.
Safe handling and storage information : Avoid contact with eyes, skin and clothing. Remove and wash contaminated clothing and footwear before re-use. Avoid breathing vapours or spray mists. For commercial and industrial use only. Store in original closed containers.
Product compatibility : Compatible with most metals and surfaces used in hospitals.
Microbiological data:
When used as directed Virex II256 contains 660 ppm of active quaternary germicide making it highly effective against a wide variety of pathogenic microorganisms.

Using approved AOAC test methods under Good Laboratory Practices, in the presence of 400 ppm hard water, 10 % serum load and 10 minutes contact time, unless otherwise noted, AutoSCP Solutions – Spick & Span Disinfector kills the following on hard non-porous inanimate surfaces:

Bacteria:
  • Pseudomonas aeruginosa, (ATCC15442)
  • Staphylococcus aureus, (ATCC 6538)
  • Salmonella cholerasuis, (ATCC 10708)
  • Acinetobacter calcoaceticus, (ATCC 9957)
  • Bordetella bronchiseptica, (ATCC 10580)
  •  Burkholderia cepacia, (ATCC 25416) formerly known as Pseudomonas cepacia
  • Campylobacter fetus, (ATCC 27374)
  • Chlamydia psittaci, (VR-125)
  • Citrobacter freundii, (ATCC 8090)
  • Enterobacter agglomearns, (ATCC 27155)
  • Enterobacter cloacae, (ATCC 23355)
  • Enterobacter liquefaciens, (ATCC 14460)
  • Enterococcus faecalis, (ATCC 19433) formerly known as Streptococcus faecalis
  • Enterococcus hirae, (ATCC 10541)
  • Escherichia coli, (ATCC 11229)
  • Escherichia coli 0157:H7, (ATCC 43890)
  • Flavobacterium meningosepticum, (ATCC 13253)
  • Haemophilus influenza, (ATCC 10211)
  • Hafnia alvei, (ATCC 13337) . Klebsiella oxytoca, (ATCC 13182)
  • Klebsiella pneumoniae, (ATCC 13883)
  • Legionella pneumophila, (ATCC 33153)
  • Listeria monocytogenes, (ATCC 15313)
  • Micrococcus luteus, (ATCC 4698)
  • Micrococcus luteus, (ATCC 14452)
  • Micrococcus sedentarius, (ATCC 27573)
  • Neisseria gonorrhae, (ATCC 43069)
  • Pasteurella multocida, (ATCC 43137)
  • Proteus mirabilis, (ATCC 9240)
  • Proteus vulgaris, (ATCC 13315)
  • Pseudomonas diminuta, (ATCC 11568)
  • Pseudomonas fluorescens, (ATCC 13525)
  • Pseudomonas putida, (ATCC12633)
  • Pseudomonas stutzeri, (ATCC 17588)
  • Salmonella choleraesuis pullorum, (ATCC 19945)
  • Salmonella enteritidis, (ATCC 13076)
  • Salmonella gallinarum, (ATCC 9184)
  • Salmonella schottmuelleri, (ATCC 10719)
  • Salmonella typhi, (ATCC 6539)
  • Salmonella typhimurium, (ATCC 13311)
  • Serratia marcescens, (ATCC 9103)
  • Shigella dysenteriae, (ATCC 29026)
  • Shigella flexneri, (ATCC 25875)
  • Shigella sonnei, (ATCC 25931)
  • Staphylococcus aureus, (ATCC 25923)
  • Staphylococcus aureus (Toxic Shock), (ATCC 33586)
  • Staphylococcus epidermis, (ATCC 14990)
  • Staphylococcus haemolyticus, (ATCC 29970)
  • Streptococcus agalactiae, (ATCC 13813)
  • Streptococcus mutans, (ATCC 25175)
  • Streptococcus pyogenes, (ATCC 19615)
  • Streptococcus pyogenes (“Strep A”- Flesh eating strain), (clinical isolate)
  • Vibrio cholera, (ATCC 11623)
  • Yersinia enterocolitica, (ATCC 9610)
Antibiotic-Resistant Bacteria
  • E. coli (ATCC 55244); Resistant to Kanamycin
  • E. coli (ATCC 47041); Resistant to Tetracycline
  • Enterococcus faecalis (ATCC 51299); Resistant to Vancoycin (VRE)
  • Klebsiella oxytoca (ATCC 15764); Resistant to Ampicillin, Dihydrostreptomycin
  • Micrococcus sedentarius (ATCC 27573); Resistant to Methicillin
  • Staphylococcus aureus (CDC HIP-5836); Intermediate Vancomycin Resistance (VISA)
  • Staphylococcus aureus (ATCC 14154); Resistant to Erythromycin, Penicillin, Streptomycin, Tetracycline
  •  Staphylococcus aureus (ATCC 33592); Resistrant to Methicillin [MRSA], Gentamicin [GRSA]
  • Staphylococcus epidermis (ATCC 51625); resistant to Methicillin [MRSE]
  • Streptococcus pneumoniae (ATCC 51915); Resistant to Penicillin [PRSP]
Viruses
  • Cytomgalovirus, (VR 538)
  • Herpes simplex Type 1, (VR 733)
  • Herpes simplex Type 2, (VR 734)
  • Human Coronavirus (VR 740)
  • Influenza Type A2(HongKong), (VR 544)
  • Parainfluenza Type 3, (VR 93)
  • Respiratory syncytial virus,(VR 26)
  • Rotavirus, (Strain WA)
  • Vaccinia virus (small pox vaccine virus), (VR 119) Kills HIV-1 (AIDS virus) (HTLV – NIB) when used as directed on hard, non-porous inanimate surfaces with a 1 minute contact time.
  • Kills HBV and HCV when used as directed on hard, non-porous inanimate surfaces with a 5 minute contact time.
Veterinary Virus
  • Avian Infectious bronchitis (IBV), (VR 22)
  • Avian Influenza, (VR 2072)
  • Canine distemper, (VR 128)
  • Feline virual rhinotracheitis, (VR 636)
  • Infectious bovine rhinotraheitis, (VR 188)
  • New Castle disease, (VR 108)
  • Pseudorabies, (VR135)
  • Transmissible gastroenteritis virus (TGE), (U of Minn. Strain) Fungi
  • Geotrichum candidum, (ATCC 18301)
  • Saccharomyces cerevisiae, (ATCC 2601)
Using approved AOAC test methods under Good Laboratory Practices, in the presence of 400 ppm hard water, 5 % serum load and 10 minutes contact time, unless otherwise noted, Virex II 256 kills the following on hard non-porous inanimate surfaces :
Viruses
  • Adenovirus Type 2, (VR 2)
Fungi
  • Aspergillus niger, (ATCC 6275)
  • Trichophyton mentagrophytes (athlete’s foot fungus), (ATCC 9533)
Yeast
  • Candida albicans, (ATCC 10231) Mold/ Midew: Kills the growth of mold and mildew; Aspergillus niger (ATCC 6275) and the odors caused by them when applied to hard, non-porous environmental surfaces.
  • Mildewstatic Activity – Controls and prevents the growth of mold and mildew: Aspergillus niger (ATCC 6275) and the odors caused by them when applied to hard, non-porous environmental surfaces.
  • Malodors – Eliminates odors and odor-causing bacteria in restroom areas, behind and under sinks and counters, garbage cans, and storage areas and other places where bacterial growth can cause malodors. Bactericidal Stability of Use – Dilution Tests show Virex II 256, when diluted in 400 ppm hard water and in the presence of 5 % serum load, remains effective against Pseudomonas aeruginosa, Staphylococcus aurus and Salmonella choleraesuis for up to 1 year in storage as long as it remains sealed. If product becomes visibly dirty or contaminated, the use-dilution must be discarded and fresh product prepared. Always use clean, dry containers when diluting this product.
Reference
  1. A Guide to selection and use of disinfectants, BC centre for disease control, 2003.
  2. Antiseptics and Disinfectants: Activity, Action and Resistance, Clinical microbiology reviews, Jan.1999, p. 147-179 Vol. 12 No.1.
  3. CDC Guidelines for Infection Control in Dental Health-Care Settings 2003, Vol. 52/RR-17.
  4. Infection Control in Dental Practice, Dental Services Division, Ministry of Health Malaysia, 1996
  5. Infection Control Policies and Procedures, Wake Forest University Health Sciences, November 1998.
  6. Therapeutic Products Programme Guidelines, Minister of Health Canada, 1999 Edition.
  7. WHO Guidelines on Hand Hygiene in Health Care, 15 January 2006.
  • Emergency Overview : Danger. Corrosive. Causes Skin and Eye burns. Harmful or fatal if swallowed. Combustible liquid and vapour.
  • Principle routes of exposure : Eye contact. Skin contact. Inhalation.
  • Eyes : Corrosive. Causes permanent damage including blindness.
  • Skin : Corrosive. Causes permanent damage.
  • Inhalation : May cause irritation and corrosive effects to nose, throat and respiratory tract.
  • Ingestion : May be irritating to mouth, throat and stomach.
  • Inhalation : If breathing is affected, remove to fresh air. If person is not breathing, call an ambulance and then give artificial respiration, preferably by mouth to mouth, if possible. Get medical attention immediately.
  • Skin contact: Take off contaminated clothing. Rinse immediately with plenty of water for 15-20 minutes. Get medical attention immediately.
  • Eye contact: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eyes. Get medical attention immediately.
  • Ingestion : Call a doctor or poison control center immediately for treatment advice. Have person sip a glass of water if able to swallow. Do not induce vomiting unless told to do so by a poison control center or doctor. Never give anything by mouth to an unconsciousness person.
  • Notes to Physician : Probable mucosal damage may contraindicate the use of gastric lavage.
  • Aggravated Medical Conditions : Individuals with chronic respiratory disorders such as asthma, chronic bronchitis, emphysema, etc., may be more susceptible to irritating effects.
FIRE FIGHTING MEASURES
  • Suitable extinguishing media : Use dry chemical, C02, water spray or “alcohol” foam.
  •  Specific hazards : Although this product has a flash point below 200°F, it is an aqueous solution containing an alcohol and does not sustain combustion.
  • Unusual hazards : Corrosive material (see Sections 8 and 10)
  • Specific methods : No special methods required.
  • Special protective equipment for firefighters : As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear.
  •  Extinguishing media which must not be used for safety reasons : No information available.
ACCIDENTAL RELEASE MEASURES
  • Protection of personnel: Put on appropriate personal protective equipment (see Section 8)
  • Environmental precautions and Clean-up Method : Clean-up methods – Large spillage. Remove all sources of ignition. Absorb spill with inert material (eg. dry sand or earth), then place in a chemical waste container. Use a water rinse for a final clean-up.
HANDLING AND STORAGE :
Handling (see also sections 8 and 15) Avoid contact with eyes, skin and clothing. Do not taste or swallow. Avoid breathing vapors or spray mists. Use only with adequate ventilation. Remove and wash contaminated clothing and footwear before re-use. Wash thoroughly after handling. Product residue may remain on/in empty containers. All precautions for handling the product must be used in handling the empty container and residue.
Storage : Protect from freezing. Keep tightly closed in a dry cool and well-ventilated place.
KEEP OUT OF REACH OF CHILDREN.
EXPOSURE CONTROLS AND PERSONAL PROTECTION
  • Engineering Controls : Good general ventilation should be sufficient to control airborne levels. Respiratory protection is not required if food ventilation is maintained.
  •  Personal Protection Equipment:
  • Breathing equipment : ln case of insufficient ventilation wear suitable respiratory equipment. A respiratory protection program that meets OSHA’s 29 CFR 1910.134 and ANSI Z88.2 requirements must be followed whenever workplace conditions warrant a respirator’s use.
  • Protection of hands : Chemical resistant gloves.
  • Eye protection : Chemical splash goggles.
  • Skin and body protection : Protective footwear. If major exposure is possible wear suitable protective clothing and footwear.
  •  Hygiene measures : If major exposure is possible, wear suitable protective clothing and footwear.
Available pack size Pack size:
  • 750 ml, 2 ltrs (for individual customers)
  • 5 ltrs for bulk purchase.
Hazard identification
CORROSIVE
Only for professional users / specialists. The manufacturer guarantees the quality of this product. Application recommendations are based on tests and practical experience; the manufacturer declines all responsibility for damages from improper product use.

AUTOSCP SOLUTIONS – SPICK & SPAN : Plot No. 7, 402, 4th floor, RKH, Viveknagar, Kukatpally, Hyderabad – 500072.

Phone : 9494565358.

For more information  mail us on Email: customercare@autoscpsolutions.com.

Website : www.AUTOSCP SOLUTIONS .com .